Leather technical data sheet: which lines bind your supplier
Every tannery sends a technical data sheet. Most buyers file it. Half of its lines describe the article in general; the other half can be held against a batch, but only if they are written the right way.
A guide by TL San Martín, a tannery of origin in Elda (Alicante, Spain) since 1995, LWG Gold certified under the Leather Manufacturer standard.
A line on a leather technical data sheet binds the supplier only when it carries four things: a value, a tolerance, a named test method and a basis (per batch or typical). \"Thickness 1.2–1.4 mm, ISO 2589\" is a commitment. \"Excellent rub fastness\" is a description. Copy the binding lines into your purchase order; ask for the rest to be rewritten.
What is a leather technical data sheet, and what is it not?
A technical data sheet (TDS) describes an article: one leather, in one construction, as the tannery normally makes it. It is not a test report on your batch (one production run, dyed and finished together), and it is not a certificate about the plant. Three documents, three levels:
| Document | Talks about | Typical question it answers |
|---|---|---|
| LWG certificate | The site | Was this plant audited, against which standard, with what medal? |
| Technical data sheet | The article | What is this leather, and what does it normally measure? |
| Test report | One batch | Did the hides you received pass, measured by a lab? |
Buyers get into trouble when they treat the middle document as if it were the third. The TDS says what the article usually does. Whether a line can be held against your delivery depends on how it is written. How the first document works is covered in how to read an LWG certificate.
Which lines are a commitment and which are a description?
Apply the same four-part test to every line: value, tolerance, test method, basis. If one of the four is missing, the line describes; it does not commit.
| Line on the TDS | Written as a description | Written as a commitment |
|---|---|---|
| Thickness | "Approx. 1.3 mm" | 1.2–1.4 mm, EN ISO 2589, at the ISO 2418 position, per batch |
| Tannage | "Eco tanned" | Chrome-free (wet-white), declared per batch |
| Finish | "Natural look" | Semi-aniline, pigmented top-coat, stated finish code |
| Rub fastness | "Excellent" | ISO 11640, dry and wet cycles stated, minimum grey-scale grade stated |
| Tear strength | "High" | ISO 3377-2, minimum load in newtons, typical or per batch stated |
| Flex resistance | "Suitable for footwear" | ISO 5402-1, cycles dry/wet, "no damage" criterion |
| Chromium VI | "Cr VI free" | Below 3 mg/kg, EN ISO 17075, report per batch |
| Breathability | "Breathable" | Water vapour permeability, ISO 14268, value in mg/cm²·h |
The numbers you need for rub, tear and flex depend on the product: a dress-shoe vamp, a bag gusset and a dog collar do not share limits. Agree them with your factory. What matters here is the form: a figure the lab can fail.
Two lines deserve suspicion when they appear without a method. "Cr VI free" is a claim, not a result: under REACH Annex XVII entry 47 (Regulation (EU) No 301/2014, in force since 1 May 2015) leather in contact with skin must stay below 3 mg/kg, and the method is EN ISO 17075. And "breathable" means nothing without a permeability figure; why that matters for minimalist footwear is in breathability claims for barefoot shoes.
Why does "typical" matter more than the number?
Most data sheets end with a small phrase: typical values or values for guidance. That phrase turns every line above it into a description. It is honest, because leather is a natural material and every hide differs, but it means nothing on the sheet can be enforced on its own.
The fix is not to ask the tannery to delete the phrase. Ask which lines it will test per batch, and write only those into the order. Usually that is thickness, colour against the approved reference and chromium VI. Physical lines such as tear and flex are tested per article or per season. Pay for a batch test when the product is safety-relevant or the order is large.
The data sheet describes the article; the document that speaks about the leather you actually received is the lab report on your batch. Which fields tie it to your order is in leather test report: what it proves about your batch.
Where can the sheet and your batch disagree legitimately?
Three places, all predictable.
- Position on the hide. Physical tests are taken at a defined position (ISO 2418), near the backbone, where the fibre is densest. Bellies are thinner and stretchier. Your cutting room uses the whole hide, so the cut parts will not all match the sheet. That is normal, and it is why yield and grade matter as much as the TDS; see what leather grades on an invoice commit to.
- Conditioning. Leather gains and loses moisture. Lab values are measured after conditioning to ISO 2419. A thickness check on a cold warehouse floor is not a test.
- Colour. A TDS rarely carries colour at all. Colour is agreed against a physical reference, not a number on a sheet. The method is in leather lab dip approval.
For thickness, the range itself is a design decision before it is a supplier commitment. What to specify by shoe type is in leather thickness for shoe uppers.
How do you turn a TDS into a purchase spec?
Five steps, done once per article and reused every season:
- Copy, don't attach. Paste the binding lines into the purchase order. An attached PDF can be updated; a line on your order cannot.
- Add the missing piece. For each line, check value, tolerance, method and basis. Ask the tannery to complete what is missing, in writing.
- Split per batch from per article. Name the two or three lines tested on every delivery; the rest stay "typical".
- Name the reference. Approved sample, approved lab dip and a retained cut of each shipped batch.
- Agree the dispute rule before the dispute. Which lab, who pays, and what happens to a batch that fails.
If you are still collecting quotes, the 12 questions to ask a leather supplier cover the commercial side. If you plan to visit, the TDS is one of the five documents in the tannery visit checklist.
At TL San Martín the data sheet comes with every article in the library and with every sample. We are LWG Gold under the Leather Manufacturer standard — the only standard in which the Gold medal exists; a Trader reaches at most "Approved". That certificate covers the plant. The TDS and the batch report cover the leather. You need all three. New to buying leather? Start at the hub, leather for shoes: what to buy first.
Post your RFQ with the spec attached
Have a spec and want tanneries to answer line by line? Post it under RFQ · Production on the open Business Board: article, thickness range, test methods and quantity. Looking for a specific leather rather than a production partner? Use Materials. Or request physical samples with the technical data sheet of the article.
Frequently asked questions
Is a technical data sheet a legal guarantee?
Only for the lines you copy into the purchase contract with a value, tolerance and method. A data sheet marked "typical values" describes the article; it does not guarantee a specific batch.
Who should pay for batch testing?
Agree it before the first order. A common rule: the tannery's own per-batch checks (thickness, colour, chromium VI) are included in the price. Extra physical tests at an external lab are paid by the buyer, unless the batch fails.
My factory measured 1.1 mm on a 1.2–1.4 mm leather. Is the batch out of spec?
Not necessarily. Ask where on the hide the factory measured and whether the leather was conditioned. If the measurement was taken at the standard position after conditioning, then yes, raise it with the batch number.
Should a TDS be updated every season?
The article sheet changes only when the recipe changes. Ask for the revision date on every sheet, and ask to be told when it changes. A new recipe under an old article name is the most common source of "same leather, different behaviour".
TL San Martín tans and finishes leather in Elda, Alicante, since 1995: LWG Gold under the Leather Manufacturer standard — the only standard under which a Gold medal exists at all; a Trader tops out at “Approved”. Request samples before you specify anything.